IT & Infrastructure

30 tools

Plan IP networks, estimate bandwidth and transfer times, size storage, and calculate practical server and infrastructure capacity.

Calculator guides

IP & Subnetting

Network Performance

Storage & RAID

Server Capacity

Advanced network and storage planning

Transparent formulas
Every result shows the calculation steps.
Locale-aware
Dates, decimals and units match your language.
No sign-up
Free and instant — no account needed.

How to choose the right calculator

“What is the network, broadcast and host range of 192.168.10.37/26?” → IPv4 Subnet Calculator. “Which prefix fits 500 hosts?” → IPv4 Host Calculator (or CIDR Calculator for raw addresses). Converting between /24, 255.255.255.0 and 0.0.0.255 → Subnet Mask Converter or Wildcard Mask Calculator. A start and end address you need as CIDR blocks → IP Range Calculator. IPv6 addressing and how many /64s a /48 holds → IPv6 Subnet and IPv6 Prefix. “Is 100 Mbps really 12.5 MB/s?” → Mbps to MB/s; any other rate pair → Bandwidth Converter. “How long will this copy take?” → Data Transfer Time; “what link do I need to finish by 06:00?” → Required Bandwidth; a long fat link that will not fill → Bandwidth-Delay Product; a realistic figure after overhead → Network Throughput Estimate. Usable capacity of an array → RAID Capacity; after reserves, filesystem overhead and replication → Usable Storage; storage performance → IOPS and Disk Throughput; backup fits the night window → Backup Window; log retention sizing → Log Storage. How many VMs a host holds → VM Density; vCPU-to-core ratio → CPU Oversubscription; memory headroom → RAM Capacity; consumption and electricity cost → Server Power.

About this category

Plan IP networks, estimate bandwidth and transfer times, size storage, and calculate practical server and infrastructure capacity. These tools cover the arithmetic that sysadmins, network and DevOps engineers, hosting operators and homelab users repeat constantly: turning a prefix into a usable host range, converting Mbit/s to MB/s, working out how long a 20 TB backup needs, or how many VMs a host really fits.

Every calculation runs in your browser and is deterministic: nothing is looked up, pinged, geolocated or sent to a server, so entering a real address or hostname reveals nothing. IPv4 arithmetic is exact 32-bit, IPv6 uses arbitrary precision and never borrows IPv4 broadcast semantics, and SI units (MB = 10⁶ bytes) are kept strictly apart from IEC units (MiB = 2²⁰ bytes). Capacity and throughput results are nominal planning figures — they state their assumptions rather than pretending to predict what a specific array, hypervisor or link will deliver.

Frequently asked questions

Why does a /31 or /32 not show “2ⁿ − 2” usable hosts?

The classic formula subtracts the network and broadcast addresses, which only exist in ordinary subnets. A /31 is a two-address point-to-point link on which both addresses are usable (RFC 3021), and a /32 is a single host with no broadcast address at all. The calculators label these two cases explicitly instead of reporting 0 or −1 hosts.

Why is 100 Mbps not 100 MB/s, and why is my 2 TB drive 1.82 TB in the OS?

Two different confusions, both about units. Network rates are in bits per second, storage in bytes, and one byte is eight bits — so 100 Mbit/s = 12.5 MB/s. Separately, drives are sold in SI units (2 TB = 2 × 10¹² bytes) while most operating systems report IEC units (1 TiB = 2⁴⁰ bytes), so the same drive shows as ≈1.82 TiB. These tools always name the exact unit and never silently treat 1 GB as 1024 MB.

Will the RAID calculator tell me the capacity my server actually reports?

No — it gives nominal capacity from the equal-drive formulas (RAID 5 = (N−1) × S, RAID 6 = (N−2) × S, RAID 10 = (N/2) × S, and so on). Filesystem overhead, metadata, hot spares, vendor reservations, compression and deduplication are not included, because they depend on your controller and filesystem. Use Usable Storage afterwards to apply reserved space, overhead and replication.

Related categories